482 lines
19 KiB
C
482 lines
19 KiB
C
/*
|
||
*****************************************************************
|
||
头文件
|
||
*****************************************************************
|
||
*/
|
||
#include "usart4.h"
|
||
|
||
/*
|
||
************************************************************************************
|
||
变量定义
|
||
************************************************************************************
|
||
*/
|
||
char temp_data[100];
|
||
//串口接收缓存区
|
||
u8 USART4_TX_BUF[USART4_MAX_SEND_LEN]; //发送缓冲
|
||
|
||
/*
|
||
*********************************************************************************************************
|
||
* 函 数 名: USART4_Configuration()
|
||
* 功能说明: 串口4配置
|
||
* 输 入 ：波特率baund
|
||
* 输 出 ：无
|
||
*********************************************************************************************************
|
||
*/
|
||
void USART4_Configuration(u32 baund)
|
||
{
|
||
USART_InitTypeDef USART_InitStructure;
|
||
GPIO_InitTypeDef GPIO_InitStructure;
|
||
NVIC_InitTypeDef NVIC_InitStructure;
|
||
|
||
RCC_APB1PeriphClockCmd(RCC_APB1Periph_UART4, ENABLE); //使能USART4
|
||
RCC_AHBPeriphClockCmd(RCC_AHBPeriph_GPIOC, ENABLE); //GPIOc时钟
|
||
|
||
USART_DeInit(UART4); //复位串口1
|
||
|
||
//USART1_TX PA.9
|
||
GPIO_InitStructure.GPIO_Pin = GPIO_Pin_11 | GPIO_Pin_10;
|
||
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AF;
|
||
GPIO_InitStructure.GPIO_Speed = GPIO_Speed_10MHz;
|
||
GPIO_InitStructure.GPIO_OType = GPIO_OType_PP;
|
||
GPIO_InitStructure.GPIO_PuPd = GPIO_PuPd_UP;
|
||
GPIO_Init(GPIOC, &GPIO_InitStructure);
|
||
|
||
//USART1_RX PA.10
|
||
GPIO_InitStructure.GPIO_Pin = GPIO_Pin_11;
|
||
GPIO_Init(GPIOC, &GPIO_InitStructure);
|
||
|
||
GPIO_PinAFConfig(GPIOC, GPIO_PinSource11, GPIO_AF_UART4);
|
||
GPIO_PinAFConfig(GPIOC, GPIO_PinSource10, GPIO_AF_UART4);
|
||
|
||
USART_InitStructure.USART_BaudRate = baund;
|
||
USART_InitStructure.USART_WordLength = USART_WordLength_8b;
|
||
USART_InitStructure.USART_StopBits = USART_StopBits_1;
|
||
USART_InitStructure.USART_Parity = USART_Parity_No;
|
||
USART_InitStructure.USART_HardwareFlowControl = USART_HardwareFlowControl_None;
|
||
USART_InitStructure.USART_Mode = USART_Mode_Rx | USART_Mode_Tx;
|
||
USART_Init(UART4,&USART_InitStructure);
|
||
|
||
USART_Cmd(UART4,ENABLE);
|
||
|
||
//Usart1 NVIC 配置
|
||
NVIC_InitStructure.NVIC_IRQChannel = UART4_IRQn;//串口1中断通道
|
||
NVIC_InitStructure.NVIC_IRQChannelPreemptionPriority=5;//抢占优先级3
|
||
NVIC_InitStructure.NVIC_IRQChannelSubPriority =0; //子优先级3
|
||
NVIC_InitStructure.NVIC_IRQChannelCmd = ENABLE; //IRQ通道使能
|
||
NVIC_Init(&NVIC_InitStructure); //根据指定的参数初始化VIC寄存器、
|
||
USART_ITConfig(UART4,USART_IT_RXNE,ENABLE);//开启USART1的接收中断和空闲中断
|
||
USART_ClearFlag(UART4,USART_FLAG_TC); //清除发送完成标志位
|
||
USART_ITConfig(UART4,USART_IT_IDLE,ENABLE);//开启USART1的接收中断和空闲中断
|
||
}
|
||
|
||
/*
|
||
*********************************************************************************************************
|
||
* 函 数 名: Usart4_ReceiveBuff_Clear()
|
||
* 功能说明: 串口4清空缓冲区
|
||
* 输 入 ：无
|
||
* 输 出 ：无
|
||
*********************************************************************************************************
|
||
*/
|
||
void Usart4_ReceiveBuff_Clear(void)
|
||
{
|
||
ESP8266_Fram_Record_Struct .InfBit .FramFinishFlag=0;
|
||
ESP8266_Fram_Record_Struct .InfBit .FramLength=0;
|
||
memset(ESP8266_Fram_Record_Struct.Data_RX_BUF,0,RX_BUF_MAX_LEN);
|
||
//memset(USART4_TX_BUF,0,USART4_MAX_SEND_LEN);
|
||
}
|
||
|
||
/*
|
||
*********************************************************************************************************
|
||
* 函 数 名: UART4_IRQHandler()
|
||
* 功能说明: 串口4中断函数
|
||
* 输 入 ：无
|
||
* 输 出 ：无
|
||
*********************************************************************************************************
|
||
*/
|
||
void UART4_IRQHandler(void)
|
||
{
|
||
u8 ucCh;
|
||
|
||
if(USART_GetITStatus( UART4, USART_IT_RXNE ) != RESET )
|
||
{
|
||
ucCh = USART_ReceiveData( UART4 );
|
||
|
||
if(ESP8266_Fram_Record_Struct .InfBit .FramLength < ( RX_BUF_MAX_LEN - 1 ) )
|
||
{
|
||
//留最后一位做结束位
|
||
ESP8266_Fram_Record_Struct .Data_RX_BUF[ ESP8266_Fram_Record_Struct .InfBit .FramLength ++ ] = ucCh;
|
||
}
|
||
else
|
||
{
|
||
ESP8266_Fram_Record_Struct .InfBit .FramLength = 0;
|
||
ESP8266_Fram_Record_Struct .InfBit .FramFinishFlag = 1;
|
||
}
|
||
}
|
||
|
||
if(USART_GetITStatus( UART4, USART_FLAG_ORE ) != RESET )
|
||
{
|
||
USART_ReceiveData(UART4);
|
||
USART_ClearFlag(UART4, USART_FLAG_ORE);
|
||
}
|
||
|
||
if( USART_GetITStatus( UART4, USART_IT_IDLE ) != RESET ) //如果总线空闲
|
||
{
|
||
ESP8266_Fram_Record_Struct .InfBit .FramFinishFlag = 1;
|
||
ucCh = USART_ReceiveData( UART4 ); //由软件序列清除中断标志位（先读USART_SR,然后读USART_DR）
|
||
}
|
||
}
|
||
|
||
/*
|
||
*********************************************************************************************************
|
||
* 函 数 名: u4_printf()
|
||
* 功能说明: 串口4输出
|
||
* 输 入 ：
|
||
* 输 出 ：
|
||
*********************************************************************************************************
|
||
*/
|
||
void u4_printf(char* fmt,...)
|
||
{
|
||
u16 i,j;
|
||
va_list ap;
|
||
va_start(ap,fmt);
|
||
vsprintf((char*)USART4_TX_BUF,fmt,ap);
|
||
va_end(ap);
|
||
i=strlen((const char*)USART4_TX_BUF); //此次发送数据的长度
|
||
for(j=0;j<i;j++) //循环发送数据
|
||
{
|
||
while(USART_GetFlagStatus(UART4,USART_FLAG_TC)==RESET); //循环发送,直到发送完毕
|
||
USART_SendData(UART4,USART4_TX_BUF[j]);
|
||
}
|
||
}
|
||
|
||
/*
|
||
*********************************************************************************************************
|
||
* 函 数 名: USART4_Recieve_Ide()
|
||
* 功能说明: WIFI交互
|
||
* 输 入 ：无
|
||
* 输 出 ：无
|
||
*********************************************************************************************************
|
||
*/
|
||
u8 USART4_Recieve_Ide(void)
|
||
{
|
||
u8 i = 0;
|
||
u16 temp_u16=0;
|
||
char *recString;
|
||
char *recStringNext;
|
||
char adda;
|
||
char year_head[3];
|
||
char hhmmss[7]={'\0'},yymmdd[10]={'\0'};
|
||
char test[100]={"\r\n+IPD,0,52:parw-2,\"111.198.24.44\",1883,licawifi,88888888,8080,\"lichao\",\"910517@lc\",\"bc25test\",*"};
|
||
Init_Data Init_Data_Equipment_temp;
|
||
Init_Data_Equipment_temp=Read_Equipment_Par();//读取设备参数
|
||
if( ESP8266_Fram_Record_Struct .InfBit .FramFinishFlag==1)
|
||
{
|
||
/************恢复出厂设置参数***********/
|
||
if((strstr(ESP8266_Fram_Record_Struct.Data_RX_BUF, "parw-rst")!=NULL))//接收恢复出厂设置
|
||
{
|
||
Write_Factory_Par();
|
||
EEPROM_ReadBytes(140,&Par_store_flag,1);
|
||
if(Par_store_flag)ESP8266_SendString(DISABLE,"parw-rst,OK,*",13,0);
|
||
else ESP8266_SendString(DISABLE,"parw-rst,fail,*",15,0);
|
||
|
||
}
|
||
|
||
/*写入******设备ID、测量间隔、预约时间、测量模式、远传时间*********/
|
||
if((strstr(ESP8266_Fram_Record_Struct.Data_RX_BUF, "parw-1")!=NULL))//判断接收信息是否是命令参数设置
|
||
{
|
||
memset(temp_data,0,100);
|
||
for (i = 0 ; i < 5 ; i++)
|
||
{
|
||
if (i == 0)
|
||
{
|
||
if ((recString = strstr(ESP8266_Fram_Record_Struct.Data_RX_BUF, "parw-1")) == NULL)
|
||
;
|
||
recString+=6;
|
||
}
|
||
else
|
||
{
|
||
recString++;
|
||
if((recStringNext = strstr(recString, ",")) != NULL)
|
||
{
|
||
switch(i)
|
||
{
|
||
case 1: memset(Init_Data_Equipment.Equipment_ID,0,10);
|
||
memcpy(Init_Data_Equipment.Equipment_ID, recString, recStringNext - recString);
|
||
|
||
case 2: memset(Init_Data_Equipment.Measure_Interval,0,5);
|
||
memcpy(Init_Data_Equipment.Measure_Interval, recString, recStringNext - recString);
|
||
temp_u16=hexToDec(Init_Data_Equipment.Measure_Interval);
|
||
memset(Init_Data_Equipment.Measure_Interval,0,5);
|
||
sprintf(Init_Data_Equipment.Measure_Interval,"%d",temp_u16);
|
||
break; //获取测量间隔
|
||
case 3: memset(Init_Data_Equipment.appointment_time,0,appointment_time_len);
|
||
memcpy(Init_Data_Equipment.appointment_time, recString, recStringNext - recString);break; //预约时间
|
||
case 4: memset(Init_Data_Equipment.measure_mode,0,1);
|
||
memcpy(Init_Data_Equipment.measure_mode, recString, recStringNext - recString);break; //测量模式
|
||
|
||
default:break;
|
||
}
|
||
}
|
||
recString=recStringNext;
|
||
if(i==4)
|
||
{
|
||
recString++;
|
||
recStringNext=strstr(recString,",*");
|
||
memset(Init_Data_Equipment.Pub_Time,0,Pub_Time_len);
|
||
memcpy(Init_Data_Equipment.Pub_Time, recString, recStringNext - recString);
|
||
temp_u16=hexToDec(Init_Data_Equipment.Pub_Time);//
|
||
if(temp_u16<1)temp_u16=1;
|
||
memset(Init_Data_Equipment.Pub_Time,0,Pub_Time_len);
|
||
sprintf(Init_Data_Equipment.Pub_Time,"%d",temp_u16);
|
||
}
|
||
}
|
||
}
|
||
|
||
if(hexToDec(Init_Data_Equipment.Measure_Interval)<1)//测量间隔时间min
|
||
sprintf(Init_Data_Equipment.Measure_Interval,"%s","00001");//测量间隔最小60S
|
||
Write_Equipment_Par(Init_Data_Equipment);
|
||
ESP8266_SendString(DISABLE,"parw-1,OK,*",11,0);
|
||
if(strcmp(Init_Data_Equipment_temp.Equipment_ID,Init_Data_Equipment.Equipment_ID)||
|
||
strcmp(Init_Data_Equipment_temp.Measure_Interval,Init_Data_Equipment.Measure_Interval)||
|
||
strcmp(Init_Data_Equipment_temp.appointment_time,Init_Data_Equipment.appointment_time)||
|
||
strcmp(Init_Data_Equipment_temp.measure_mode,Init_Data_Equipment.measure_mode)||
|
||
strcmp(Init_Data_Equipment_temp.Pub_Time,Init_Data_Equipment.Pub_Time))
|
||
{
|
||
Init_Data_Equipment.par_change=1;
|
||
EEPROM_WriteBytes(185, &Init_Data_Equipment.par_change,1);
|
||
}
|
||
|
||
if((Init_Data_Equipment.measure_mode[0]=='1') && (IsAppointmentRight()))
|
||
{
|
||
Measure_Ap_S();
|
||
}
|
||
if(strcmp(Init_Data_Equipment_temp.measure_mode,Init_Data_Equipment.measure_mode)==0)//模式未变
|
||
{
|
||
|
||
}
|
||
else//模式改变
|
||
{
|
||
if(Init_Data_Equipment.measure_mode[0]=='0')
|
||
Measure_Ap_E();
|
||
}
|
||
}
|
||
/*写入******远传IP、远传端口、wifi名称、wifi密码、wifi端口*********/
|
||
if((strstr(ESP8266_Fram_Record_Struct.Data_RX_BUF, "parw-2")!=NULL)&(strstr(ESP8266_Fram_Record_Struct.Data_RX_BUF, "\"")!=NULL))
|
||
{
|
||
//memcpy(ESP8266_Fram_Record_Struct.Data_RX_BUF,test,100);
|
||
for (i = 0 ; i < 9 ; i++)
|
||
{
|
||
if (i == 0)
|
||
{
|
||
if ((recString = strstr(ESP8266_Fram_Record_Struct.Data_RX_BUF, "parw-2")) != NULL)
|
||
;//解析错误
|
||
recString+=6;
|
||
}
|
||
else
|
||
{
|
||
recString++;
|
||
if((recStringNext = strstr(recString, ",")) != NULL)
|
||
{
|
||
switch(i)
|
||
{
|
||
case 1: memset(Init_Data_Equipment.Bc25_Ip,0,20);
|
||
memcpy(Init_Data_Equipment.Bc25_Ip, recString, recStringNext - recString);break; //iot ip
|
||
case 2: memset(Init_Data_Equipment.Bc25_Port,0,10);
|
||
memcpy(Init_Data_Equipment.Bc25_Port, recString, recStringNext - recString);break; //iot port
|
||
case 3: memset(Init_Data_Equipment.ESP8266_AP_SSIDs,0,20);
|
||
memcpy(Init_Data_Equipment.ESP8266_AP_SSIDs, recString, recStringNext - recString);break; //wifi 名称
|
||
case 4: memset(Init_Data_Equipment.ESP8266_AP_PWDs,0,10);
|
||
memcpy(Init_Data_Equipment.ESP8266_AP_PWDs, recString, recStringNext - recString);break; //wifi 密码
|
||
|
||
case 5: memset(Init_Data_Equipment.ESP8266_AP_Ports,0,10);
|
||
memcpy(Init_Data_Equipment.ESP8266_AP_Ports, recString, recStringNext - recString);break; //服务器名称
|
||
|
||
case 6: memset(Init_Data_Equipment.IOT_Username,0,20);
|
||
memcpy(Init_Data_Equipment.IOT_Username, recString, recStringNext - recString);break; //服务器名称
|
||
case 7: memset(Init_Data_Equipment.IOT_Password,0,20);
|
||
memcpy(Init_Data_Equipment.IOT_Password, recString, recStringNext - recString);break; //服务器密码
|
||
case 8: memset(Init_Data_Equipment.IOT_Theme_name,0,20);
|
||
memcpy(Init_Data_Equipment.IOT_Theme_name, recString, recStringNext - recString);break; //主题名称
|
||
|
||
default:break;
|
||
}
|
||
}
|
||
recString=recStringNext;
|
||
}
|
||
|
||
}
|
||
// memcpy(Init_Data_Equipment.ESP8266_AP_Ports, recString+1, 4); //获取wifi port
|
||
Write_Equipment_Par(Init_Data_Equipment);
|
||
ESP8266_SendString(DISABLE,"parw-2,OK,*",11,0);
|
||
if(strcmp(Init_Data_Equipment_temp.Bc25_Ip,Init_Data_Equipment.Bc25_Ip)||
|
||
strcmp(Init_Data_Equipment_temp.Bc25_Port,Init_Data_Equipment.Bc25_Port)||
|
||
strcmp(Init_Data_Equipment_temp.ESP8266_AP_SSIDs,Init_Data_Equipment.ESP8266_AP_SSIDs)||
|
||
strcmp(Init_Data_Equipment_temp.ESP8266_AP_PWDs,Init_Data_Equipment.ESP8266_AP_PWDs)||
|
||
strcmp(Init_Data_Equipment_temp.ESP8266_AP_Ports,Init_Data_Equipment.ESP8266_AP_Ports)||
|
||
strcmp(Init_Data_Equipment_temp.IOT_Username,Init_Data_Equipment.IOT_Username)||
|
||
strcmp(Init_Data_Equipment_temp.IOT_Password,Init_Data_Equipment.IOT_Password)||
|
||
strcmp(Init_Data_Equipment_temp.IOT_Theme_name,Init_Data_Equipment.IOT_Theme_name)
|
||
)
|
||
|
||
{
|
||
Init_Data_Equipment.par_change=1;
|
||
EEPROM_WriteBytes(185, &Init_Data_Equipment.par_change,1);
|
||
}
|
||
}
|
||
|
||
/*写入******立刻启动测量*********/
|
||
if((strstr(ESP8266_Fram_Record_Struct.Data_RX_BUF, "parw-3")!=NULL))
|
||
{
|
||
if ((recString = strstr(ESP8266_Fram_Record_Struct.Data_RX_BUF, "parw-3,1")) != NULL)
|
||
{
|
||
//u5_printf("TASKRUNSS.Test_RUN :%d\r\n",TASKRUNSS.Test_RUN);
|
||
if(TASKRUNSS.Test_RUN)//判断测量任务是否被占用
|
||
{
|
||
//ESP8266_SendString(DISABLE,"parw-3,busy\r\n",13,0);
|
||
ESP8266_SendString(DISABLE,"parw-3,OK,*",11,0);
|
||
}else
|
||
{
|
||
//TASKRUNSS.Test_RUN=1;
|
||
MYITStatus1.WKUP_Test_WIFI=1;
|
||
//
|
||
ESP8266_SendString(DISABLE,"parw-3,OK,*",11,0);
|
||
}
|
||
MYITStatus1.WKUP_Test_WIFI=1;
|
||
}
|
||
if ((recString = strstr(ESP8266_Fram_Record_Struct.Data_RX_BUF, "parw-3,0")) != NULL)
|
||
{
|
||
//用于停止扩展
|
||
}
|
||
|
||
}
|
||
/*设置******系统时间*********/
|
||
if((recString=strstr(ESP8266_Fram_Record_Struct.Data_RX_BUF, "parw-4")) !=NULL)
|
||
{
|
||
memset(temp_data,0,100);
|
||
recString+=7;
|
||
memcpy(temp_data, recString, 13); //获取系统时间
|
||
if(((temp_data[4]-'0')*10+(temp_data[5]-'0')*1)>12|
|
||
((temp_data[6]-'0')*10+(temp_data[7]-'0')*1)>31|
|
||
((temp_data[8]-'0')*10+(temp_data[9]-'0')*1)>23|
|
||
((temp_data[10]-'0')*10+(temp_data[11]-'0')*1)>59|
|
||
((temp_data[12]-'0')*10+(temp_data[13]-'0')*1)>59)
|
||
{
|
||
ESP8266_SendString(DISABLE,"parw-4,fail,*",13,0);
|
||
|
||
}else
|
||
{
|
||
SetRTC(
|
||
((temp_data[2]-'0')*10+(temp_data[3]-'0')*1),
|
||
((temp_data[4]-'0')*10+(temp_data[5]-'0')*1),
|
||
((temp_data[6]-'0')*10+(temp_data[7]-'0')*1),
|
||
((temp_data[8]-'0')*10+(temp_data[9]-'0')*1),
|
||
((temp_data[10]-'0')*10+(temp_data[11]-'0')*1),
|
||
((temp_data[12]-'0')*10+(temp_data[13]-'0')*1)
|
||
);
|
||
DS3231_Set(
|
||
((temp_data[2]-'0')*10+(temp_data[3]-'0')*1),
|
||
((temp_data[4]-'0')*10+(temp_data[5]-'0')*1),
|
||
((temp_data[6]-'0')*10+(temp_data[7]-'0')*1),
|
||
((temp_data[8]-'0')*10+(temp_data[9]-'0')*1),
|
||
((temp_data[10]-'0')*10+(temp_data[11]-'0')*1),
|
||
((temp_data[12]-'0')*10+(temp_data[13]-'0')*1)
|
||
);
|
||
EEPROM_WriteBytes(170,(u8*)temp_data,2);
|
||
|
||
|
||
if((RTC->CR)&0x100)//已经开启了远传闹钟
|
||
{
|
||
RTC_AlarmAConfig(get_pubidv());
|
||
}
|
||
if((RTC->CR)&0x200)//已经开启间隔闹钟
|
||
{
|
||
RtcWakeUpConfig(get_meaidv() - 1);
|
||
}
|
||
ESP8266_SendString(DISABLE,"parw-4,OK,*",11,0);
|
||
Init_Data_Equipment.par_change=1;
|
||
EEPROM_WriteBytes(185, 0,1);
|
||
}
|
||
}
|
||
|
||
/*写入******传感器地址修改*********/
|
||
if((recString=strstr(ESP8266_Fram_Record_Struct.Data_RX_BUF, "parw-5")) !=NULL) //parw-aAb,0A1
|
||
{
|
||
recString=strstr(recString, ",");
|
||
recString++;
|
||
recStringNext=recString+2;
|
||
Sdi_chanegadd(recString[0],recStringNext[0]);
|
||
adda=Sdi_Readone(recStringNext[0]);
|
||
if(adda==0)
|
||
{
|
||
ESP8266_SendString(DISABLE,"parw-5,OK,*",11,0);
|
||
//数值相同
|
||
}else
|
||
ESP8266_SendString(DISABLE,"parw-5,fail,*",13,0);
|
||
|
||
|
||
}
|
||
/*读取******设备ID、测量间隔、预约时间、测量模式、远传时间*********/
|
||
if((recString=strstr(ESP8266_Fram_Record_Struct.Data_RX_BUF, "parr-1")) !=NULL)
|
||
{
|
||
//&&(strstr(ESP8266_Fram_Record_Struct.Data_RX_BUF, "\r\n"))!=NULL)
|
||
memset(temp_data,0,100);
|
||
|
||
Init_Data_Equipment=Read_Equipment_Par();
|
||
sprintf(temp_data,"parr-1,%s,%d,%s,%s,%d,*",
|
||
Init_Data_Equipment.Equipment_ID,
|
||
hexToDec(Init_Data_Equipment.Measure_Interval),
|
||
(Init_Data_Equipment.appointment_time),
|
||
(Init_Data_Equipment.measure_mode),
|
||
hexToDec(Init_Data_Equipment.Pub_Time)
|
||
);
|
||
ESP8266_SendString(DISABLE,temp_data,strlen(temp_data),0);
|
||
}
|
||
|
||
/*读取******远传IP、远传端口、wifi名称、wifi密码、wifi端口*********/
|
||
if(strstr(ESP8266_Fram_Record_Struct.Data_RX_BUF, "parr-2"))
|
||
{
|
||
memset(temp_data,0,100);
|
||
GetRTC(hhmmss,yymmdd);
|
||
sprintf(temp_data,"%s,%s,%s,%s,%s,%s,*",
|
||
"parr-2",
|
||
Init_Data_Equipment.Bc25_Ip,
|
||
Init_Data_Equipment.Bc25_Port,
|
||
Init_Data_Equipment.ESP8266_AP_SSIDs,
|
||
Init_Data_Equipment.ESP8266_AP_PWDs,
|
||
Init_Data_Equipment.ESP8266_AP_Ports
|
||
);
|
||
ESP8266_SendString(DISABLE,temp_data,strlen(temp_data),0);
|
||
|
||
}
|
||
|
||
/*读取******系统时间 日期*********/
|
||
if(strstr(ESP8266_Fram_Record_Struct.Data_RX_BUF, "parr-4"))
|
||
{
|
||
memset(temp_data,0,100);
|
||
GetRTC(hhmmss,yymmdd);
|
||
EEPROM_ReadBytes(170, (u8*)year_head,2);
|
||
sprintf(temp_data,"%s,%s%s,%s,*","parr-4",year_head,yymmdd,hhmmss);
|
||
ESP8266_SendString(DISABLE,temp_data,strlen(temp_data),0);
|
||
}
|
||
|
||
/*读取******传感器地址查询*********/
|
||
if((recString=strstr(ESP8266_Fram_Record_Struct.Data_RX_BUF, "parr-s?")) !=NULL)
|
||
{
|
||
memset(temp_data,0,100);
|
||
adda=Sdi_readaddress();
|
||
if(adda!=0x7f)
|
||
{
|
||
sprintf(temp_data,"Address:%c,*",adda);
|
||
ESP8266_SendString(DISABLE,temp_data,strlen(temp_data),0);
|
||
}
|
||
else
|
||
ESP8266_SendString(DISABLE,"Address,fail,*",14,0);
|
||
|
||
}
|
||
Usart4_ReceiveBuff_Clear();
|
||
}
|
||
return 0;
|
||
}
|
||
|
||
/***************************** END OF FILE *********************************/
|