v2.9

lib/SparkFun u-blox Arduino Library/examples/Example14_DebugOutput/Example14_DebugOutput.ino

@@ -0,0 +1,93 @@
+/*
+  Reading lat and long via UBX binary commands using UART @38400 baud - free from I2C
+  By: Nathan Seidle, Adapted from Example3_GetPosition by Thorsten von Eicken
+  SparkFun Electronics
+  Date: January 28rd, 2019
+  License: MIT. See license file for more information but you can
+  basically do whatever you want with this code.
+
+  This example shows how to configure the debug output from the library.
+  Debug shows various packet and status outputs. These prints can be directed
+  towards Serial (as in Serial.print) or any other port (Serial1, SerialUSB, etc).
+
+  Feel like supporting open source hardware?
+  Buy a board from SparkFun!
+  ZED-F9P RTK2: https://www.sparkfun.com/products/15136
+  NEO-M8P RTK: https://www.sparkfun.com/products/15005
+  SAM-M8Q: https://www.sparkfun.com/products/15106
+
+  Hardware Connections:
+  Connect the U-Blox serial TX pin to Uno pin 10
+  Connect the U-Blox serial RX pin to Uno pin 11
+  Open the serial monitor at 115200 baud to see the output
+*/
+
+#include "SparkFun_Ublox_Arduino_Library.h" //http://librarymanager/All#SparkFun_u-blox_GNSS
+SFE_UBLOX_GPS myGPS;
+
+long lastTime = 0; //Simple local timer. Limits amount if I2C traffic to Ublox module.
+
+void setup()
+{
+  Serial.begin(115200);
+  while (!Serial); //Wait for user to open terminal
+  Serial.println("SparkFun Ublox Example");
+
+  Wire.begin();
+
+  if (myGPS.begin() == false) //Connect to the Ublox module using Wire port
+  {
+    Serial.println(F("Ublox GPS not detected at default I2C address. Please check wiring. Freezing."));
+    while (1);
+  }
+
+  myGPS.setI2COutput(COM_TYPE_UBX); //Set the I2C port to output UBX only (turn off NMEA noise)
+  myGPS.saveConfiguration(); //Save the current settings to flash and BBR
+
+  myGPS.enableDebugging(); //Enable debug messages over Serial (default)
+  //myGPS.enableDebugging(SerialUSB); //Enable debug messages over Serial USB
+
+}
+
+void loop()
+{
+  //Query module only every second. Doing it more often will just cause I2C traffic.
+  //The module only responds when a new position is available
+  if (millis() - lastTime > 1000)
+  {
+    lastTime = millis(); //Update the timer
+    
+    long latitude = myGPS.getLatitude();
+    Serial.print(F("Lat: "));
+    Serial.print(latitude);
+
+    long longitude = myGPS.getLongitude();
+    Serial.print(F(" Long: "));
+    Serial.print(longitude);
+    Serial.print(F(" (degrees * 10^-7)"));
+
+    long altitude = myGPS.getAltitude();
+    Serial.print(F(" Alt: "));
+    Serial.print(altitude);
+    Serial.print(F(" (mm)"));
+
+    byte SIV = myGPS.getSIV();
+    Serial.print(F(" SIV: "));
+    Serial.print(SIV);
+
+    Serial.println();
+    Serial.print(myGPS.getYear());
+    Serial.print("-");
+    Serial.print(myGPS.getMonth());
+    Serial.print("-");
+    Serial.print(myGPS.getDay());
+    Serial.print(" ");
+    Serial.print(myGPS.getHour());
+    Serial.print(":");
+    Serial.print(myGPS.getMinute());
+    Serial.print(":");
+    Serial.println(myGPS.getSecond());
+    
+    Serial.println();
+  }
+}