91 lines
3.1 KiB
C++
91 lines
3.1 KiB
C++
/*
|
|
By: Paul Clark
|
|
SparkFun Electronics
|
|
Date: December, 2020
|
|
License: MIT. See license file for more information but you can
|
|
basically do whatever you want with this code.
|
|
|
|
This example configures the High Navigation Rate on the NEO-M8U and then
|
|
polls and displays the attitude solution, vehicle dynamics information
|
|
and high rate position, velocity and time.
|
|
|
|
This example polls the high rate data.
|
|
(The next example uses "autoHNR" to receive the HNR data automatically.)
|
|
|
|
Please make sure your NEO-M8U is running UDR firmware >= 1.31. Please update using u-center if necessary:
|
|
https://www.u-blox.com/en/product/neo-m8u-module#tab-documentation-resources
|
|
|
|
Feel like supporting open source hardware?
|
|
Buy a board from SparkFun!
|
|
NEO-M8U: https://www.sparkfun.com/products/16329
|
|
|
|
Hardware Connections:
|
|
Plug a Qwiic cable into the GPS and a Redboard Qwiic
|
|
If you don't have a platform with a Qwiic connection use the
|
|
SparkFun Qwiic Breadboard Jumper (https://www.sparkfun.com/products/14425)
|
|
Open the serial monitor at 115200 baud to see the output
|
|
|
|
*/
|
|
|
|
#include <Wire.h> //Needed for I2C to GPS
|
|
|
|
#include <SparkFun_Ublox_Arduino_Library.h> //http://librarymanager/All#SparkFun_u-blox_GNSS
|
|
SFE_UBLOX_GPS myGPS;
|
|
|
|
void setup()
|
|
{
|
|
Serial.begin(115200);
|
|
while (!Serial); //Wait for user to open terminal
|
|
Serial.println(F("SparkFun u-blox Example"));
|
|
|
|
Wire.begin();
|
|
|
|
//myGPS.enableDebugging(); // Uncomment this line to enable debug messages on Serial
|
|
|
|
if (myGPS.begin() == false) //Connect to the Ublox module using Wire port
|
|
{
|
|
Serial.println(F("Warning! u-blox GPS did not begin correctly."));
|
|
Serial.println(F("(This may be because the I2C port is busy with HNR messages.)"));
|
|
}
|
|
|
|
myGPS.setI2COutput(COM_TYPE_UBX); //Set the I2C port to output UBX only (turn off NMEA noise)
|
|
myGPS.saveConfigSelective(VAL_CFG_SUBSEC_IOPORT); //Save (only) the communications port settings to flash and BBR
|
|
|
|
if (myGPS.setHNRNavigationRate(10) == true) //Set the High Navigation Rate to 10Hz
|
|
Serial.println(F("setHNRNavigationRate was successful"));
|
|
else
|
|
Serial.println(F("setHNRNavigationRate was NOT successful"));
|
|
}
|
|
|
|
void loop()
|
|
{
|
|
// Poll and print selected HNR data
|
|
if (myGPS.getHNRAtt(125) == true) // Request HNR Att data using a 125ms timeout
|
|
{
|
|
Serial.print(F("Roll: "));
|
|
Serial.print(myGPS.hnrAtt.roll);
|
|
Serial.print(F(" Pitch: "));
|
|
Serial.print(myGPS.hnrAtt.pitch);
|
|
Serial.print(F(" Heading: "));
|
|
Serial.println(myGPS.hnrAtt.heading);
|
|
}
|
|
if (myGPS.getHNRDyn(125) == true) // Request HNR Dyn data using a 125ms timeout
|
|
{
|
|
Serial.print(F("xAccel: "));
|
|
Serial.print(myGPS.hnrVehDyn.xAccel);
|
|
Serial.print(F(" yAccel: "));
|
|
Serial.print(myGPS.hnrVehDyn.yAccel);
|
|
Serial.print(F(" zAccel: "));
|
|
Serial.println(myGPS.hnrVehDyn.zAccel);
|
|
}
|
|
if (myGPS.getHNRPVT(125) == true) // Request HNR PVT data using a 125ms timeout
|
|
{
|
|
Serial.print(F("ns: "));
|
|
Serial.print(myGPS.hnrPVT.nano);
|
|
Serial.print(F(" Lat: "));
|
|
Serial.print(myGPS.hnrPVT.lat);
|
|
Serial.print(F(" Lon: "));
|
|
Serial.println(myGPS.hnrPVT.lon);
|
|
}
|
|
}
|